COURS.

Electrical Engineering for Non-Electrical Engineers

Mississauga, ON / les 24, 25 et 26 mars 2020 /
Code : 10-0210-2373

Inscrivez-vous
La confirmation du cours dépend de votre inscription. Inscrivez-vous tôt pour éviter que le cours soit reporté ou annulé.
  • APERÇU
  • PROGRAMME
  • FORMATEUR
  • ENDROIT

APERÇU

After participating in this course you will be able to:

  • Understand and apply electrical code requirements
  • Design electrical systems in compliance with the code
  • Broaden your knowledge of electrical equipment, wire and cable applications
  • Relate electrical code to grounding and bonding requirements
  • Determine the code requirements for motor applications, substations, and high voltage lines

Description
This course focuses on basic electrical design concepts that will meet the demands of industrial and commercial design, construction, and maintenance. In addition to familiarizing participants with basic electrical circuits and circuit parameters, the course provides a general understanding of the methods used to design low voltage power distribution systems (600 volts or less).

The course will emphasize the Canadian Electrical Code while introducing the basics of electrical generation, transmission and distribution, design philosophy and procedures, construction materials, services, grounding, and power quality.

Course Outline

  • Electric power & circuit fundamentals
  • Power quality
  • Major electrical equipment
  • Electrical power generation
  • Load characteristics & conductor sizing
  • Fault calculation & protection system
  • Standards & codes
  • Design procedures
  • Motor branch circuit design
  • Feeder circuit design

Who Should Attend
Non-Electrical Engineers • Project Engineers • Operations & Maintenance Engineers • Managers • Construction personnel • Plant & Facility Engineers • Inspectors & Municipal personnel • Electrical Contractors

voir le programme complet

PROGRAMME

Daily Schedule:
8:00 Registration and Coffee (Day I only)
8:30 Session begins
12:00 Lunch (provided)
4:30 Adjournment

There will be a one-hour lunch break each day in addition to refreshment and networking breaks during the morning and afternoon.

Day I

Welcome, Introduction, Workshop Preview, Learning Outcomes, and Assessment Method

Introduction to Electrical Engineering

Electric Power Fundamentals

  • Basic electrical units
  • Circuit arrangement
  • Alternating current relation
  • Transformers
  • Voltage terminology and standards

Electric Circuits Fundamentals

  • AC circuit theory
  • Single phase and three phase systems
  • Inductance, capacitance, and impedance
  • Active power, reactive power, and power factor
  • Examples

Power Quality

  • Introduction
  • Types of disturbances
  • Power quality monitoring
  • Power quality mitigation techniques

Major Electrical Equipment

  • Generators
  • Transformers
  • Motors
  • Capacitors
  • Lighting
  • Switchgears
  • Electrical construction materials

Day II

System Design Philosophy

Electrical Power Generation, Transmission, and Distribution

  • Fundamentals of power generation, transmission, and distribution
  • Substation concept
  • Overhead vs. underground cables
  • One-line diagrams

Load Characteristics and Conductor Sizing Consideration

  • Load characteristics
  • Load study/possible loads
  • Ampacity tables
  • Voltage regulation calculations

Fault Calculation and Protection System Fundamentals

  • Fault types
  • Fault calculations
  • Protection system fundamentals
  • Over-current coordination

Standards, Recommended Practices, Guides, and Codes

  • Introduction to Canadian Electrical Code
  • Key relevant sections of the Canadian Electrical Code

Day III

Design Procedures

Lighting and Non-motor Branch Circuit Design

  • Harmonics consideration
  • CEC requirements
  • Circuit protection
  • Calculations

Motor Branch Circuit Design

  • Electric Motors
  • CEC requirements
  • Motor protection
  • Circuit protection
  • Calculations

Feeder Circuit Design

  • CEC requirements
  • Circuit protection
  • Calculations

Service Design

  • Commercial/industrial examples
  • CEC constraints
  • Utility constraints
  • Equipment
  • Switchboards
  • Metering: CTs, PTs

Questions and Answers, Feedback on Achievement of Learning Outcomes

FORMATEUR

Ajit Bapat, P.Eng., M.Eng., MBA

Ajit is well known in the electrical distribution field for his 40 years of expertise in the art and science of ground fault protection.

He holds Master's degrees in business administration and electrical engineering, specializing in power systems and power system protection. He has particular interest in ground fault protection; digital metering systems; microprocessor based integrated systems for protection; and the metering, monitoring, and control of power distribution systems. A member of Professional Engineers Ontario, he is also a senior life member of the IEEE.




ENDROIT

EPIC Learning Center
5670 McAdam Rd
Mississauga, ON L4Z 1T2
1-888-374-2338

HÔTEL - Code de réductionFor hotels close to EPIC/Special room rates, please email rsubben@epictraining.ca
INSCRIVEZ-VOUS
VOUS N’ÊTES PAS INTERESSÉ PAR CE COURS ?

Nous visons toujours à améliorer la qualité de nos cours. Veuillez sélectionner les raisons pour lesquelles vous pensez que ce cours est inadéquat (Cochez toutes les cases qui s’appliquent).

Svp cochez cette case :
Note d’évaluation pour cette formation
4.3 sur 5

Évaluation globale de ce cours par ses participants précédents !

UNITÉS & FRAIS
  • 2,1 Unités de formation continue (UFC)
  • 21 Heures de développement professionnel (HDP)

2295 $ (+ TPS/TVQ)

Inscrivez-vous




Accumulez vos
UFC / HDP

Tous les cours du CIPE vous permettent d’obtenir vos UFC / HDP ; utiles pour ceux qui doivent accumuler et soumettre leurs HDP comme l’exige l’Ordre des ingénieurs du Québec.

Ces exigences de formation prennent fin le 31 mars 2021 !

VOIR LES COURS
ABONNEZ-VOUS POUR RESTER BIEN INFORMÉ

Ne pas manquer cette
occasion !

Recevez les dernières offres, des rapports liés à l'industrie, l'offre des cours à venir, et plus - tout simplement en vous inscrivant ci-dessous.

Abonnez-vous
Formation en entreprise

Les AVANTAGES de la formation en entreprise :

  • Efficacité et coût
  • Des cours de grandes qualité
  • Flexibilité
  • Pratique
  • Confidentialité
  • Offre des UFC / HDP (Unités de formation continue / Heures de développement professionnel). Obtenez un certificat avec des unités de formation continue (UFC). Une UFC vaut 10 HDP (Heures de développement professionnel).
En savoir plus
Top